Review

hitachi im4000plus ion milling system (Hitachi Ltd)

Hitachi Ltd is a verified supplier

Hitachi Ltd manufactures this product

About

News

Press Release

Team

Advisors

Partners

Contact

Bioz Stars

Bioz vStars

Buy from Supplier

Structured Review

Hitachi Ltd hitachi im4000plus ion milling system
Hitachi Im4000plus Ion Milling System, supplied by Hitachi Ltd, used in various techniques. Bioz Stars score: 97/100, based on 1153 PubMed citations. ZERO BIAS - scores, article reviews, protocol conditions and more
https://www.bioz.com/product/hitachi+im4000+system/IM4000/pmc13165927-297-19-19
Average 97 stars, based on 1153 article reviews

hitachi im4000plus ion milling system - by Bioz Stars, 2026-09

97/100 stars

Images

other:

Article Title: Influence of multilayer architecture on microstructure and fracture properties of arc evaporated TiAlTaN coatings
Article Snippet: Therefore, coating cross-sections were prepared by ion milling with a Hitachi IM4000+ system.

Article Title: Evolution of the fracture properties of arc evaporated Ti1-xAlxN coatings with increasing Al content
Article Snippet: Using this SEM, also cross-sections of the coatings, which were prepared by ion-milling with a Hitachi IM4000+ system, were investigated.

Article Title: High-Resolution Investigation of the Interfaces in Cathodic Arc Evaporated TiN/CrAlN Multilayer Coatings
Article Snippet: The cross-section was prepared by broad ion beam milling, which was conducted via a Hitachi IM4000+ system (Hitachi High-Tech Corporation, Tokyo, Japan).

Suspension:

Article Title: Effects of rolling conditions on the microstructure and mechanical properties in a Mg–Al–Ca–Mn–Zn alloy sheet
Article Snippet: Microstructures and microtextures were characterized using Carl Zeiss Cross Beam 1540EsB equipped with HKL EBSD detector. .. The EBSD samples were metallographically prepared using SiC papers and 50 nm diameter silica suspension, and subsequently argon ion beam milled using Hitachi IM4000 system. .. X-ray diffraction (XRD) was performed to measure macro-scale texture in Rigaku SmartLab 4-Axis diffractometer using Cu-Kα radiation at 40 kV with 200 mA.

Article Title: Elucidating dynamic precipitation and yield strength of rolled Mg–Al–Ca–Mn alloy
Article Snippet: Microstructures and micro-textures were characterized using Carl Zeiss Cross Beam 1540EsB equipped with HKL EBSD detector. .. The EBSD samples were metallographically prepared using SiC papers and 50 nm diameter silica suspension (water-free), and subsequently argon ion beam milled with a low voltage (2 kV) for 1 h using Hitachi IM4000 system. ..

Article Title: Elucidation of formation and transformation mechanisms of Ca-rich Laves phase in Mg-Al-Ca-Mn alloys
Article Snippet: .. The samples for EBSD were metallographically prepared using SiC papers and 50 nm diameter silica suspension (water-free), and subsequently argon ion beam milled for 1 h using Hitachi IM4000 system. .. TEM samples and APT specimens were prepared by an in-situ lift-out method [28,29] in a focused ion beam (FIB) instrument FEI Helios Dual Beam SEM/FIB 600/600i.

Microscopy:

Article Title: Transport mechanisms during the high-temperature oxidation of ternary γ/γ′ Co-base model alloys
Article Snippet: .. High quality of each cross-section is essential and is achieved by argon ionmilling with the Hitachi IM4000 system for surface finishing prior to analysis in a field-emission scanning electron microscope (Hitachi FE-SEM S-4800) and to obtain clear EBSD pattern. .. Distances were directly determined from the BSE micrographs with the imaging software ImageJ.